How to Specify Custom RV Fitted Sheets for Shaped Mattresses
UN fitted sheet for a shaped caravan mattress is cut to the outline and depth of that mattress and held in position by its lower edge.
Mattress outline
The outline of the base determines the cut outline of the sheet with the addition of an allowance for ease of fit and for seam(s).
The outline of a shaped mattress may be dissected into a number of straight lines and circular arcs.
A fitted sheet for a shaped mattress may be cut from a single piece of fabric or from two pieces joined by a seam. The location of the seam(s) will vary according to the fabric width and the outline of the mattress. It is preferable to locate the seam(s) in the least conspicuous position(s).
At the corners, where the fabric is gathered, allowance must be made for the reduction in depth due to gathering. The allowance at a corner will vary with:
• the radius of the corner
• the depth of the mattress and
• the elasticity of the fabric.
Corner shapes
Mattresses on caravan sites can have rounded corners of many radii. In most instances the sheet is cut to the same corner radius. The corner shape normally dictates the way in which the lower edge of the sheet is closed.
The depth of the sheet is the distance from the top to the bottom edge at the side. If the mattress has a deep crown, the depth should be sufficient to ensure the lower edge of the sheet is not lifted off the bottom of the mattress when the crown is compressed in use.
The fitted sheet is secured by elasticated tape along the whole or parts of the lower edge.
Mattress depth
The fitted sheet when laid on to the mattress should drop down over the sides and, if required, over the ends. The seat or mattress required to be fitted will be of a known depth.
The fitted sheet must cover the top surface and the sides, and more specifically must have a side, or wall, deep enough to provide sufficient tuck-under all round the mattress.
The fabric measure, or depth, of the fitted sheet might need to accommodate any cushioning or bedding which is to be tucked under the mattress.
The mattress depth, plus an allowance for tuck-under and for hemming, determines the depth of the fitted border and the width of the top panel to which it is sewn, or the extent by which a cloth is shaped larger than the mattress.
Handed patterns
The pattern shape is not a true rectangle. A fitted sheet, therefore has a definite top edge and bottom edge, and when viewed towards the top from the bottom it has a left-hand and a right-hand side.
Elastic and seams
– The seams should not be puckered at the corners.
– The elastic should be securely attached.
– The sheet should be easy to apply to the mattress.
Where the mattress is very deep and the sheet has a platform, adequate fabric should be allowed so that the corners do not pull out.
Access to the bed
The position of the access area from which the bed is made up and used must be identified.
If there is access from both sides of the bed, then tuck-in depths at both sides must be measured.
Note: In a caravan, the access side may be the long side of the bed; not the end.
The bed maker needs working room to lift the mattress corner and to reach under it.
Fitting trial
It is essential that the correct fit of the sheet be verified prior to final making up. A fitting trial will reveal any discrepancies in the cut dimensions and in the position of the seam line. A trial fitting also allows the seam line to be adjusted and pinned so that the contour is smooth and firm. The position of the label and of any other identification marks should also be checked at this stage.
Record the seam allowance for comparison with the value specified in the cut sheet.
Laundering trial
The sheet has to cover the top surface and sides of the mattress completely and, after being fitted in position, has to be free from creases. Any shrinkage that prevents the sheet going on easily, or causes it to become tight across the top while leaving the base detached, will result in rejection of the sheet. The sheet should be laundered according to the care instructions and before and after measurements compared.
Fit the laundered sample to the same mattress and check again for creases around the shaped corners. Check that the lower edge of the sheet does not rise above the base of the mattress when in position.
Order records
The following details appear to be necessary for the proper execution of an order:
(a) The cut size which the customer requires or the measurements on which this is to be based, from which the cut size is calculated by the maker. (b) The type of fabric with details of any pattern which requires matching or positioning. (c) The position of the trade name or label where specified. (d) The type of elasticized edge required, including whether elastic is sewn round the whole of the hem or only part, and if only part, the length over which the elastic is to be applied, and its position in the hem. (e) The make up details where these differ from standard, for example a stitch type other than lockstitch. (f) The method of packing if other than standard.
Preparing an enquiry
Tessile HSC lists biancheria da letto per roulotte and fitted sheets in its product range. Buyers can send a dimensioned sketch and identify the mattress model when discussing an order.
Siamo un gruppo aziendale che integra produzione e commercio: ULAND GROUP. Le nostre filiali includono HSC Textiles, Liaocheng Shanlian Textile Co., Ltd., Zhongfei e DDL.

