A fitted sheet for a commercial mattress is cut to the outline and depth of that mattress and held in position by its lower edge.
The outline of the base determines the cut outline of the sheet with the addition of an allowance for ease of fit and for seam(s).
Mattress outline and core measurement
The outline of a commercial mattress consists of a rectangular deck and four vertical side walls. The core depth must be measured with a rigid rule while the mattress rests uncompressed on a flat support deck.
Mattresses on commercial sites can have depths of many dimensions. In most instances the sheet is cut to the known depth of the mattress. The mattress required to be fitted will be of a known depth, with the addition of any topper or protective pad which is to remain on the bed.
Pocket depth calculation
The depth of the sheet is the distance from the top surface to the bottom elasticated edge.
The mattress depth, plus an allowance for tuck-under and for hemming, determines the cut depth of the pocket border:
- a tuck-under allowance of 7 cm to 8 cm is standard for mattresses up to 25 cm depth
- a tuck-under allowance of 10 cm is required for deep commercial mattresses to ensure the lower edge is not lifted off the bottom of the mattress when the crown is compressed in use.
HSC Textile commercial bedsheet manufacturing options for custom hospitality orders.
Elastic and hem construction
The fitted sheet is secured by elasticated tape along the whole or parts of the lower edge.
At the lower edge, where the fabric is gathered, allowance must be made for the reduction in depth due to gathering. The allowance along the lower edge will vary with:
- whether the elastic is applied all round the hem or only at the corners
- the depth of the mattress and
- the tension of the elastic.
The elastic should be securely attached. The tunnel hem is closed with lockstitch or chain stitch. Joining of the elastic ends must overlap by not less than 30 mm with multi-step zig-zag stitching.
Fabric selection
The type of fabric determines the durability of the sheet and its behavior in laundering.
The fabric may be cut from combed cotton in a sateen weave or in a percale weave. The choice of weave will vary according to the required surface texture and the laundering routine. Combed cotton yarn and bamboo viscose options give balanced tensile strength and a smooth finish.
The fabric measure should be sufficient to prevent the sheet being transparent over dark mattress ticking, while allowing water extraction during washing.
Marge de retrait
Allowance must be made for the reduction in dimensions due to laundering.
Cotton weaves exhibit between 3% and 5% shrinkage in length and 2% to 3% in width during commercial hot-water washing. The cut dimensions of the deck panel and the pocket border must be enlarged by this percentage.
Where pre-shrunk fabric is specified, dimensional change after washing is held within 2%.
Corner seams
The vertical corner seams take the strain when the sheet is fitted to the mattress:
- the seams should not be puckered at the corners
- the corner seam must be closed with a four-thread overlock or a reinforced French seam to enclose raw edges
- the junction between the vertical corner seam and the deck panel must be back-tacked for not less than 15 mm.
Fitting and laundering trials
It is essential that the correct fit of the sheet be verified prior to final making up. A fitting trial will reveal any discrepancies in the cut dimensions and in the position of the seam line.
The sheet has to cover the top surface and sides of the mattress completely and, after being fitted in position, has to be free from creases.
Launder the trial sample according to commercial care instructions and compare before and after measurements. Fit the laundered sample to the same mattress and check that the lower edge of the sheet does not rise above the base of the mattress when the mattress is occupied.
Order records
The following details appear to be necessary for the proper execution of an order:
(a) The cut size which the customer requires or the mattress measurements on which this is based, from which the cut size is calculated by the maker.
(b) The tuck-under allowance required.
(c) The type of fabric with thread count and basis weight.
(d) The type of elasticized edge required, including whether elastic is sewn round the whole of the hem or only part, and if only part, the length over which the elastic is to be applied, and its position in the hem.
(e) The make up details where these differ from standard, for example a stitch type other than lockstitch.
(f) The method of packing if other than standard.
Preparing an enquiry
HSC Textile lists commercial bedding and fitted sheets in its product range. A dimensioned sketch and the mattress model number may be forwarded when discussing an order.
HSC Textile custom fitted sheet production line for hotel and healthcare clients.
À propos de HSC Textiles
We are a group company integrating manufacturing and trade – ULAND GROUP. Our subsidiaries include HSC Textiles, Liaocheng Shanlian Textile Co., Ltd., Zhongfei.

